Open Assembly Co. logoOpen Assembly Co.
§ Material Inventory · /inv

Register what you already have.

Reclaimed material is not treated as generic stock. Each piece keeps its dimensions, condition, and history, and the system designs the connection around it.

§ 01

New material profile

input
Upload photos

Drop images of each face and edge.

input
Scan with phone / LiDAR

Capture rough geometry, accuracy not required.

input
Enter dimensions manually

L × W × T in mm. Add tolerances if uneven.

input
Add material type

Pine · oak · ply · MDF · unknown

input
Add condition tags

Honest tags help suggest the right joints.

input
Add source / history

Where it came from. What it used to be.

Condition tags · pick honestly
warpeddrilledpaintedcrackedunevenworncut edgeunknown strengthprevious furniture partworkshop offcut

→ Honest tags improve joint suggestions. A "warped" board will be matched to flex clamps, not rigid corners.

Save
Save material profile

Pieces stay in your inventory and can be matched to any future assembly.

§ 02

My inventory

800 × 220 × 18 mm
M.01
Old shelf board
Previous flat
painteddrilled
690 × 60 × 15 mm
M.02
Bed slat
Child's outgrown bed
wornflexible
340 × 90 × 20 mm
M.03
Offcut
Workshop waste
uneven edge
1200 × 180 × 22 mm
M.04
Reclaimed board
Glasgow Wood
markedsolid
500 × 500 × 12 mm
M.05
Plywood scrap
Studio waste
cut edgedrilled
1800 × 45 × 45 mm
M.06
Pine batten
Marketplace
warpedworn

→ Reclaimed material is not treated as generic stock. Each piece keeps its dimensions, condition, and history.

§ 03

Material Sourcing Guide

Sources
source
Reuse & reclaim centres

Glasgow Wood, local timber reuse

source
Old furniture

Children's beds, desks, shelves

source
Workshop scraps

University, makerspace offcuts

source
Studio waste

Designer offcuts, leftover stock

source
Community searching

Marketplace, freecycle, neighbours

source
Your own flat

Previous shelves, bed slats, panels

Practical guidance
G.01
What to look for

Solid grain, square edges where you need them, repairable surfaces.

G.02
What to avoid

Rot, deep cracks across the grain, unknown coatings, anything sticky.

G.03
How to check basic condition

Knock test, flex by hand, look for filler and old fixings.

G.04
How to measure

Two diagonals on flat boards. Worst-case L × W × T.

G.05
When not to use a material

If a failure would be load-bearing on a person, pick a safer cousin.

G.06
Safety notes

Old paint may contain lead. Ventilate. Wear PPE when sanding or cutting.

§ 04

Sources near you

→ Click a pin for address and link. Coordinates are approximate; check before travelling.

Mapped sources
  1. Glasgow Wood
    S.01
    Reuse & reclaim centre
    56 Brand Place, Govan, G51 1DR
    visit →
  2. Glasgow School of Art, Wood Workshops
    S.02
    University workshop
    Reid Building, 164 Renfrew St, G3 6RQ
    visit →
  3. Reset Scenery
    S.03
    Set & scenery reuse
    Glasgow (by appointment)
    visit →
  4. Glasgow Tool Library
    S.04
    Tool lending + offcut share
    Sawmillfield St, G4 9QQ
    visit →
  5. Glasgow Sculpture Studios
    S.05
    Studio workshop offcuts
    The Whisky Bond, 2 Dawson Rd, G4 9SS
    visit →

Know a source we should add? Tell the community →